Somethings Must be considered to respond a Slow Computer Problem

1. Spyware and Viruses are one cause of a slow pc, because the most easily penetrated, and many users are interacting with it (indirectly), spyware comes from banners and advertisements on a web page into action when we access the page / banner with a browser that has a security hole that was not good, so that spyware is very close to the IE.
Some ways to remove spyware:

-Identification and analysis process that is running the Windows task manager.
-Identify and disable service in question through the management console.
-Identify and disable services at startup item in system configuration utilty.
-Find and delete the existing entry in the registry on startup.
-Identify and delete suspicious files.
-Install and use a spyware detection and removal.

2. Processor Overheating Most processors easy to generate heat, thus requiring special cooling and a special type of fan, so when the processor temperature increases beyond the limit, the system will slow down and the process will be slow. The processor fan that failed due to:
- Dust which inhibits smooth rotation of the fan.
- Fan motor broken.
- Bearing fan is broken so that the fan "jiggling".
Jiggling is if the fan is spinning there was a crick-crick rapidly due to bearing fan have started<$2Fspan> broken

3. Bad Ram Some situations can also be due to the influence of Bad ram, this
caused by:
-RAM timing is slower than optimal machine specifications.
-RAM has minor value will be visible only after going through several tests.
-RAM is too hot.


4. If the hard drive hard drive fail often experience failure, it will also worsen the performance of the computer, and type of fail these many causes, can be a mechanical, electronic, even the firmware is not updated, this hard drive will result in:
1. Access time is slow.
2. The number of bad sectors that continued to increase during the scandisk.
3. There are unexplained bluescreen.
4. Boot failed.

5. Bios Settings Normally bios settings that have not dicustom will experience the process of slowing down a few seconds, especially at boot time, for that we must mengcustom bios settings so that the performance of work boot process can be accelerated, in general, setting the bios to be considered are:
1. Boot directly to hard disk.
2. Disable unused IDE drives.
3. Set speed RAM latency.
4. Turn off the IO / IRQ for the onboard devices that are not used.
5. Use Fast POST.


6. Disk type / controller compatibility motherboard now usually have a good controller for the parallel ATA disks, but we must pay attention to its IDE cable, because cable has some particular specification, there is a UDMA 33, 66, and 100, if we look physically, form of the cord has a fine smooth fibers and a lot, while the UDMA 33 fibers slightly, so use a cable that has a high specification for the disk.

7. Windows Services a service that must be turned off if we do not need it is:
1. FTP 2. Indexing Service
2. remote Registry
3. telnet
4. remote Access
5. remote Desktop
6. Automatic Update

8. Sometimes the process is invisible, we know there are no programs running
in memory, even though we do not use it anymore or we even have menguninstallnya but there is still a walking program, for that we must pay attention to process what is happening in our computer by looking at task manager, and we could end taskkan or kill, then we can remove. exe it.

9. Disk fragmentation As the characteristics of files in a computer must undergo a process of the file in the add, edit, or delete it, it can lead to fragmentation in some areas of hard disk sectors, for that we need to tidy up the data on our computers, that is by mendefragnya. if we use windows xp, we can use the Defrag.exe and put it in the schedule to run at the time that we specify.

10. Background applications If we look at the systray when we click the left arrow icon will berderetlah a lot, more and more attached to the systray icon that causes the computer to respond to the slower process, because a lot of unused memory to process it, so for that we need to turn it off or disable is not necessary that by accessing the registry:
HKEY_ LOCAL_MACHINE \ Software \ Microsoft \ Windows \ CurrentVe rsion \ Run and
HKEY_LOCAL_MACHINE \ Software \ Microsoft \ Windows \ Curr entVersion \ RunOnce